Knowledge Base

Straightened material parameter

Straightened material parameters describe the characteristics of the straightened material. They can be classified in three groups:

  • Parameters of the material
  • Parameters of the cross sectional geometry
  • Parameters of the initial curvature

The straightened material parameters have an influence on the type, design and size of:

  • Straighteners and straightening systems
  • Drive units
  • Guides
  • Preforming heads
  • Postforming apparatus

Straightener/accessories

The range of accessories available for a straightener or straightenrng system can be classified according to

  • application, size and surroundings,
  • safety and operating reliability
  • handling and use,
  • design,
  • maintenance.

For each of these categories WITELS-ALBERT offers a large selection of elements and devices which are well described in the company's documentation.

The handling of a straightener, for example, largely depends on the technical elements provided to position the straightening rolls. In addition to the conventional roller positioning method using an adjusting screw it is possible to use a micrometer screw, an adjusting spindle with knurled edge, or an actuator (hydraulic cylinder, pneumatic cylinder, stepping motor or servo motor). 

Straightener/set-up

Rather than describe the straightener as a tool and its function, we want to draw attention here to its precise and modular design.

The “A” parts of a straightener's design, i.e. its basic load-bearing elements, are adapted in size to the number of rolls to be accommodated and serve as mounts for the “B” parts such as rails, grooved blocks, threaded bolts, pins and other standard parts.

The final block of this modular design are the straightening rolls. They are also the parts exposed to the greatest wear.

An approach based on the ideas of environmental management gives rise to a product and production engineering of outstanding accuracy, impressive ruggedness and durability, and
unique operability and results.

Straightening plane

The commonly held idea that the position of a straightener's body corresponds to the straightening plane is wrong.

Basically, the straightening plane is defined by the axial position of the straightening rolls. If this is horizontal, then the straightening plane is horizontal. The same applies to the curvature plane in which the product to be straightened is fed in or bent.

With a vertical axis we speak of a vertical straightening and curvature plane.

The most frequently used arrangement is the double straightener, which eliminates the initial curvatures in two planes (horizontal/vertical).

You may well ask what happens with the other curvature planes lying outside the two straightening planes? Their processing is possible at best on a random and sporadic basis or not at all.

Hence it is important when producing wire to maintain a constant curvature course and not to leave the curvature plane.

A constant straightening plane can only produce constant final curvatures from constant curvatures in the same plane.

Where this is impossible for whatever reason, the use of killing-straightener, and helix straighteners in straightening systems can prove very useful.

Straightening process set-up

A correct straightening process set-up depends on an analysis of the product to be straightened, an analysis of the straightened material production process, and an analysis of the final product. A specific procedure has to be followed in order to choose the correct straightening system, the correct number of straightening rolls, and the correct location of the one or more straighteners.

The purpose in setting up a straightening process is to determine the status quo from the essential analyses and to define the production steps and corresponding equipment needed to obtain the final product. Using our knowledge of the process we can create constant process transitions, i.e. output and input parameters, in order to produce constant final results.

Constant and reproducible straightening roll settings based on the constant input parameters known to us at the beginning of the straightening process result in a constant final curvature.

If all these aspects are duly considered, the straightener will provide optimal processing conditions for obtaining a final product of the required quality.

Straightening roll

A straightening roll is the last link in a straightener's modular design chain and the component exposed to the greatest wear. Its design, production and use thus deserves special attention.

The following criteria are particularly important:

A) Materials
The raceway of a straightening roll is subjected during roll-over to local loads which find
expression in high Hertzian surface pressures. The raceway material should be selected so that
ideally through-hardening but at least the necessary depth of hardness and a surface hardness
of 670-840 HV is achieved. The material normally used is through-hardening steel according to
DIN 17230, e.g. 100 Cr 6.

B) Bearing arrangement design
The bearing arrangement for a straightening roll is that of a locating bearing. The shaft or pin end provides radial support as well as axial guidance. Radial bearings able to absorb combined loads, e.g. radial ball bearings, angular contact ball bearings or track rollers, are suitable for use as straightening rolls. To enable the bearing's load capacity to be used to the full, the cylindrical contact faces need to be firmly and uniformly supported over their entire circumference and across the full width of the raceway. Perfect radial mounting is also vital.

C) Dynamic/static load rating
A straightening roll's dynamic load capacity depends on the fatigue behavior of its material. Fatigue time is an expression of useful life and depends on the straightening roll's loading and speed as well as on the statistical probability and random timing of the first incident of damage. Static load capacity, on the other hand, is limited by the plastic deformations produced in the raceways and rolling elements by a high resting load.

D) Bearing capacity and life-time
The size of bearing required for a specific straightening process depends firstly on the straightening range of the straightening roll. A further factor, however, is the magnitude of loading. This is expressed by the dynamic load rating C and the static load rating Co. A straightening roll's useful life is defined as the number of rotations made by its bearing before the first signs of material fatigue are noted on a raceway or rolling element.

E) Friction, speeds, and temperature
A straightening roll's frictional moment depends on many factors such as load, speed, condition of lubrication and seal friction. The maximum possible speed of a straightening roll is mainly defined by the permissible operating temperature of the rolling bearing. In other words, speed depends on the type of load, the conditions of lubrication and the conditions of cooling. A straightening roll temperature of 70°C is considered normal.

F) Dimensional, geometrical and bearing tolerances
A straightening roll's dimensional, geometrical and bearing tolerances comply with tolerance class PN conforming to DIN 620.

G) Installation and dismantling
The smooth and troublefree operation of Witels straightening rolls largely depends on the care with which they are installed and replaced. Inner rings have to be mounted on the shaft or pin so that the mounting force is evenly distributed over the front face of the inner ring. The mounting force must not be transferred to the rolling elements.

H) Lubrication, maintenance and corrosion protection
For straightening rolls to perform reliably they require sufficient lubrication to prevent direct metallic contact between the rolling elements, raceways and cage while at the same time reducing wear and protecting surfaces from corrosion. All straightening rolls are supplied with grease lubrication as standard.

J) Storage of straightening rolls
Although Witels straightening rolls are always delivered with life-time lubrication, they cannot be stored indefinitely. Under certain circumstances a straightening roll kept in storage for a long period may initially display higher frictional moments than one fresh from the factory. Nor is it possible to rule out deterioration or even gumming of the grease charge in the course of prolonged storage. Attention is drawn in this connection to the WlCAS cassette system, which finds use mainly in problematic applications for straightening rolls.