Knowledge Base

Straightening roll groove

The profile cut into the outer ring of a straightening roll is called the straightening roll groove. Its purpose is to accommodate and guide the product to be straightened.

Angular grooves of 90°, 100° or 110° are normal for round, solid material. They are particularly advantageous for straightening ranges, i.e. wire of different diameters.

Profiled, soft or tubular material, on the other hand, is straightened in grooves which are adapted to the material to be straightened to produce a non-slip fit. Smooth, unprofiled rolls are used to flatten strip material.

Straightening roll life-time

The dynamic load capacity of a straightening roll depends on its material fatigue characteristics and wear. Useful life depends on the straightening roll's loading, speed, conditions of lubrication, soiling, installation and temperature, the statistical probability of the first incidence of damage, and diverse other factors. All too often the impact of dirt is underestimated.

The load capacity and useful life of straightening rolls from Witels are determined by the methods customary in rolling bearing practice. At the same time allowance is made for the fact that the outer ring undergoes elastic deformation through contact with the product to be straightened. Compared to a rolling bearing supported in a housing bore, there is a different distribution of load in the bearing and bending stress in the outer ring. We differentiate between internal and external factors with an influence on wear.

Contact between the product to be straightened and the outer ring results in the following external factors:

  • material of the outer ring
  • material and surface consistency of the product to be straightened
  • speed
  • slip
  • soiling and lubrication

Internal factors with an influence on straightening roll wear are:

  • lubrication of the bearing
  • type of bearing
  • dynamic and static bearing load
  • speed
  • seal arrangement
  • elastic deformation

Straightening system

A straightening system is understood to be a combination of straighteners which, duly adapted to the product to be straightened, transform difficult and sometimes alternating initial material parameters into constant values.

The constant process transition thus obtained is essential for designing controlled follow-up processes.

The simplest straightening system generally consists of two individual straighteners arranged in different planes and mounted using a connecting bracket. Acceptable, constant results are achieved in many applications using a simple straightening system of this type.

If the initial parameters of the product to be straightened change during the process and if, for example, curvature fluctuations or helicities arise, then it will be necessary to use problem-related tools and jigs such as helix straighteners, killing-straighteners, etc.

A straightening system set-up consists accordingly of a clearly structured straightening process sequence. Fluctuating initial parameters require greater structuring of the straightening process to achieve a defined and constant final curvature. Simply increasing the number of straightening rolls would have little effect in this case.

The first priority is to transform changing curvatures in different planes into a constant curvature in a single plane. This is the essence of a successful straightening process with constant final curvatures.

Straightening/definition

The term “straightening” covers the actions and measures needed to eliminate process-induced curvatures in the process material in order to produce a condition of straightness, levelness or defined curvature

Stretch-bend-straightening

The term “stretch-bend-straightening” is understood to be the bending of a material around rolls of small diameter with the simultaneous application of tensile stresses. Local plastic elongation occurs in those areas where bending tensile stresses are added to tensile stresses. Upsetting can occur, on the other hand, where the bending compressive stresses superimpose on the tensile stresses. However, the biggest part of the material's cross section is subjected to a tensile load. If such a process is performed by alternate bending, the product is stretched in steps, producing a final curvature in wire material and a flatness profile in strip material.

A stretch-bend-straightening system generally consists of an infeed unit for producing a reverse tension, a straightening unit for the bending or alternate bending, and an outfeed unit for applying a forward tension. For the purpose of straightening wire, the infeed unit can be e.g. a killing-straightener and the outfeed unit can be a drive unit. The straightening unit is either a conventional straightening system, a semi-automatic straightening system or a straightening system with an automatic roll positioner.

Stretch-straightening

In the stretch-straightening process the product to be straightened is subjected to a tensile force. This results in a tensile stress inside the workpiece, which superimposes on the existing internal stresses.

The tensile force is applied in sections and at a level of magnitude designed to produce plastic deformations in the material to be straightened.