Knowledge Base

Causes of stress

Stress is the reaction of a material/workpiece to an external load. It is defined as an internal force of resistance per unit of area. There is a fundamental correlation between the condition of stress and the condition of deformation of a workpiece. A plastic deformation produces internal stresses in a workpiece which remain after the load is removed. Stresses arising during loading of such a plastically deformed workpiece are superimposed on these internal stresses. The type of stress produced during loading is characterized by the type of load. Tensile forces (drawing, coiling) result in tensile stresses while bending forces (deflecting, straightening) result in bending stresses.

Coil

For logistical reasons, products to be straightened (wire, strip, rope, etc.) are wound into coils. This entails laying the product, winding for winding, in the direction of the coil axis. If the coil is not rotated simultaneously during the laying, helicities will be produced with each winding. The product will then behave accordingly when it is pulled off. Pulling off the product statically in the direction of the coil axis will cause it to twist and the quality of the straightened product will be negatively affected by additional helicities. These curvature fluctuations and helicities are difficult to eliminate and are therefore best avoided in the first place.

The beginning and end of a coil should always be marked in order to ensure its careful and correct further processing. Constriction-free securing of the ends prevents snap-back and avoids kinks.

Coiler

A coiler is a device for the winding or unwinding of a lengthy process material.

In direct or indirect interaction with other components it is also used to create tensile stress.

Important technological sub-functions such as guiding the process material are likewise performed by a coiler.

Curvature

Curvature is understood to be a deviation from the straight.

When an endless material is wound onto a spool, the inner layers have a smaller radius of curvature and the outer layers a larger radius of curvature.

Whether or not a winding is elastic or plastic depends on the spool geometry, the properties of the endless material, and the degree of deformation.

Curvature is the reciprocal of the radius of curvature and has the dimension [1/mm].

Curvature course during straightening

The curvature course during straightening is understood to be the correct sequence of curvatures followed by the process material during the straightening process.

The initial curvature is always followed by the counter-curvature. The final curvature is the curvature remaining after spring back. This curvature sequence is repeated according to the number of straightening rolls.

A straightening process should be arranged so that, irrespective of the initial curvature, the last adjustment-induced curvature resulting after the last spring back in a final curvature corresponds to the desired straightening result. 

Decoil-straightener

The decoil-straightener is a combination of a decoiling/unspooling unit and a straightening unit used in conjunction with a material store. The endless material to be straightened is decoiled/unspooled from a coil/spool and directed to the straightening unit via several deflections (store) and a bending roll, always maintaining constant directions of deflection and curvature. Apart from the bending of the material around the bending roll, all the deflections around the pairs of pulleys are performed only elastically.

The coil/spool is rotatably mounted to enable the material to be paid off dynamically (preventing additional torsional stresses and helicities such as occur with static pay-off set-ups). The coil/spool is driven by an electric motor whose speed is controlled in accordance with the dancer position. A sensor scans the dancer position (height), producing an electric signal which is evaluated by a controller and relayed to the motor electronics.

The pull-off force acting on the material to be straightened is constant, consisting only of the straightening force and a variable dancer weight. Additional tensile forces caused by acceleration and deceleration, particularly in discontinuous processes, are minimized by the store function.

Equipped with the right mounting arrangement, users can change over quickly between various straightening devices, helix straighteners and killing-straighteners to suit the different types of material to be straightened. An additional stretch-bend-straightening effect can be produced by using a bending roll with brake, around which the material can wrap itself at least once. To produce a higher tensile stress in the material, on the other hand, a bending roll with brake should be placed in front of the straightening devices. The straightening unit normally takes the form of a straightening system with two straighteners.