Knowledge Base

Bauschinger effect

The Bauschinger effect is a special case of forming behavior among metals. It is defined as a change of material parameters due to a reversal of loading direction between two consecutive loads (e.g. tension/compression). Because of the Bauschinger effect, loading against the initial loading direction results in a distinctly lower beginning of flow (stretching limit, elongation limit). Alternating tension-compression loads result accordingly in a shift of the flow limit. The reasons are to be found in a change of the material's microstructure. Factors affecting the magnitude of the Bauschinger effect include the material, its alloying elements (particularly carbon), the number of load cycles, and the dimensions of external deformation (actual strains). 

Bend

A bend is the strain produced in long and endless bodies by external forces, resulting in internal bending moments over their cross sections. The original straightness or curvature of the bodies is changed either elastically or plastically as the result. The internal bending moments arising in every cross section as a reaction to these external bending moments lead to tensile and compressive forces, resulting in an equilibrium of forces and moments.

Bodies subjected to bending are shortened on the one side by compressive stresses while on the other side they are lengthened by tensile forces. There is a (practically Iinear) continuous transition from tensile stress to compressive stress over the cross section, with a neutral fiber that is neither stretched nor compressed and therefore stress-free.

The diagram opposite shows a wire cross section with an applied external bending moment and the resultant strain and stress characteristic.

Bending roll

A bendlng roll is a rotating roll (pulley) on which the product to be straightened is plastically deformed during a partial or complete wrap. The important point is that the product should only be bent in the direction of its initial curvature. In other words: the initial curvature, the bend and the final curvature should all lie in one plane. A change of plane along this course of curvature and bending during the straightening process will cause helicities (twisting of the product to be straightened).

Subjecting the curvature to several changes of plane has a particularly negative effect. It leads not only to curvature fluctuations, which are very difficult to eliminate, but also to extremely disadvantageous right/left helicities.

The magnitude of plastic deformation suffered by the product to be straightened depends e.g. on its material parameters and on the diameter of the bending roll.

Caliber

A caliber is a measuring instrument used as a gauge. In steel mills, gauges are used to determine the rolling gap. On straightening units, calibers are used to fix the distance between the straightening rolls.

When a caliber is placed between the open straightening rolls of a straightener, all the adjustable straightening rolls can be aligned on one line. The straightening rolls of the one row are thus parallel to the straightening rolls of the second row. It is then possible to set the zero line for the particular product to be straightened. The adjustable rolls are adjusted by an amount equal to the difference between the thickness of the caliber and the thickness of the product to be straightened. It should be note that the adjusting travel is also affected by the geometry of the product to be straightened and the geometry of the groove. Adjustment positions are reproducible at any time.

Carbon content

The carbon content of a steel wire is crucial for many of its properties. The higher the carbon content, the greater the tensile strength but the smaller the elongation to fracture. Wire with a very low carbon content is referred to as iron wire. Its tensile strength is low. Wire made of spring steel generally has a high carbon content of between 0.4 and 1.0%, resulting in high tensile strength values.

Cassette

WICAS® - WITELS CASSETTE STRAIGHTENING SYSTEM

The rolling elements mainly used in straightening processes with roll-type straighteners suffer extreme wear as the result of the high roll adjusting forces and ever higher production speeds. At the same time, metal particles contaminate the bearings and contribute likewise to a drastic shortening of rolling element life. The WITELS Cassette Straightening System called WICAS(r) was developed specifically to improve this situation.

Notable features of WICAS®:

A) Expert installation of the rolling elements in a closed housing with an additional labyrinth seal prevents practically all soiling of the bearing system, resulting in a useful life up to 30 times longer than that of a conventional straightening roll.

B) The straightening sheave can now be produced in any form, type, quality and strength irrespective of the material used for the bearing system. Oval pressing of the rolling element outer ring, against which the product to be straightened runs, is ruled out with this design.

C) The use of smaller rolling bearings at high speeds of rotation increases the peripheral speed of the larger straightening sheave. Far higher production speeds are thus possible than with conventional straightening rolls.

D) In the case of miniature straightening rolls, cutting the groove in the relatively thin outer rings weakens the straightening roll to an unacceptable degree. This does not happen with WICAS(r) because the bearing shaft as well as the straightening sheave can be made with annular grooves of any shape and size.

E) Flexible use of needle and ball bearings gives the designer considerable scope with regards to the static and dynamic bearing values.

F) It is possible to use bearings with life-time lubrication as well as systems designed for relubrication.

The above-mentioned 30-fold longer useful life of WICAS(r) compared to conventional straightening rolls greatly minimizes the cost-intensive stoppage of individual machines and complete production lines - a benefit that should not be overlooked.