Knowledge Base

Helicity

Helicity, also commonly referred to as torsion or twisting, is understood to be a curvature course adopted by wire radially rather than axially upon leaving the curvature plane. Such a curvature course can be intentional, as in the production of rope and cable where it is called the lay length, and in the production of springs where it is called the pitch.

Helicity is an undesirable condition for all follow-up processes if it is not specifically created for the product but arises unintentionally due to certain production factors. Frequent causes of helicity include overhead pulling off, static unwinding and unspooling, incorrect deflecting, frequent changes of direction, and any faulty process transitions with a negative effect on round material which rotates during processing.

Inconstant or indeed alternating helicities not only impede the process flow but also rule out final products of any required constancy.

Aids such as helix straighteners, killing-straighteners and additional straightening systems can go a long way in solving the problem. Above all, however, it is important to avoid the avoidable and to create a constant process.

Helix straightener

A wire wound into a coil or onto a spool should have only one curvature - that of the spool or coil - in one plane if the follow-up process is to proceed without difficulty. Changing preliminary processes with sometimes inconstant process transitions create helicities, i.e. twisting, in the wire.

Helicities need to be avoided or, where constant helicities are concerned, eliminated by means of a helix straightener. A helix straightener can produce as well as remove helicities.

Like a standard straightener, a helix straightener has several straightening rolls which are partly or fully arranged in familiar manner so that they can be adjusted relative to each other.

In addition to this, one or more straightening rolls can be adjusted in height. The groove of the height-adjusted straightening roll thus forces the wire unilaterally from its zero line, bending it with unequal flank pressure into a second curvature plane. Helicities are thus removed or created by force-feeding the wire through these adjustable positions.

Initial curvature

The initial curvature is the curvature displayed by the product to be straightened before it enters the straightener.

A product to be straightened does not have a single initial curvature but several, which together form the initial curvature range. The difference between the minimal initial curvature and the maximal initial curvature is the curvature range.

How do the different initial curvatures arise?

Different initial curvatures are formed, for example, during the spooling process. The inner layers of a material wound on a spool have a bigger curvature than the outer layers. Whether the material undergoes elastic or plastic bending depends on many factors such as the material, geometry and dimensions of the product, the inner and outer diameter of the spool, and the temperature during winding.

Different initial curvatures of the product to be straightened also arise from its incorrect processing or deflecting. Helicities result in addition from changes to the directions of curvature in various curvature planes.

Internal stresses

In production processes such as casting, rolling and drawing, the outer shape of a workpiece is preserved only if it is adjusted and clamped before the process is started so that any twisting of the workpiece is prevented. Alternatively, the workpiece has to be straightened again at the end of the process. When the external loading is discontinued and the temperature compensation completed, the workpiece adopts an intrinsic shape which continues to exist without the application of any external forces and moments. The only explanation for this condition is that the sum total of internal forces and moments, i.e. internal stresses, is in equilibrium.

An analysis of the longitudinal internal stresses in a drawn wire reveals tensile stresses in the core and compressive stresses at the edge. Any change of a wire's parameters, such as curvature or helicity, over its length will result in changes of its internal stresses. Straightening has been shown to change the internal stresses so that the internal stress conditions existing in the material in the unstraightened state are eliminated. The magnitude and distribution of internal stresses existing after the straightening process depends on the design of the straightening system and particularly on the adjustment of the straightening rolls. With technology from WITELS-ALBERT it is possible to minimize the internal stresses arising during the straightening process while leaving the straightened material in optimal shape.

Killing-straightening

A wire with fluctuating initial parameters, e.g. fluctuating material parameters, initial curvature and alternating internal stresses, will be left with varying final curvatures after straightening. The wire is therefore “killed” by severe bending with straightening rolls in at least one plane in order to produce a final curvature in a single plane.

This “killing” is performed by special straighteners of type TR and TRV. Through the application of severe alternating bends with small bending radii the curvature fluctuations are reduced and the wire's internal stresses changed.

If a TR or TRV straightener is used in combination with a conventional straightening system, a semi-automatic straightening system, or a straightening system with an automatic roll positioner, then the straightening result will be affected by the resulting reverse tension.

Life-time equation

The more precisely the operating conditions of a straightening roll are known or can be calculated, the more exactly and reliably its useful life can be determined.

Three different equations are available: for nominal life-time according to ISO, for modified nominal life according to ISO, and for modified nominal life-time based on a new life theory.

The simplest approach is to determine the nominal life-time according to ISO using the relevant equation.

Calculation of the nominal life-time using the equation is sufficient for conventional bearing applications.

In other applications it may be wise to take detailed account of other life-affecting factors as well. This led in 1977 to the introduction of the modified life-time equations.

In a third equation - modified nominal life-time according to the new SKF life theory - a life-time coefficient is added to take account of a fatigue load limit and various other factors affecting the lubricating conditions and the degree of soiling.

The life-time value calculated with the third equation is regarded as the period of use actually covered by a straightening roll in its life-time. As a rule this value deviates slightly from the calculated nominal life-time.