Knowledge Base

Roll-type straightener

Using a roll-type straightener it is possible to change a process material's unidimensional initial curvatures, i.e. initial curvatures in one plane, so that defined final curvatures remain after the straightening process. The bending tools of such a roll-type straightener are straightening rolls arranged in two parallel, mutually offset rows. When the rolls are accordingly adjusted, the process material is subjected to alternating bends as it passes through the straightener. The number and magnitude of these alternating bends must be such that the initial curves are changed in defined manner over the complete length of the product to be straightened.

To straighten a product over its complete length it has to be transported relative to the straightener.
For this purpose, straightening machines are equipped with driven rolls. By contrast, the rolls on a straightener are not driven, i.e. additional devices such as drive units, pull-in units, drivers or the like are required to transport the product to be straightened.

In other words, a straightening machine has technical elements for transporting as well as straightening the product, whereas a straightener has only elements for straightening it. By this definition it is possible to use straighteners in straightening machines.

Straighteners can be classified in terms of their degree of automation. WITELS-ALBERT offers products for conventional straightening, semi-automatic straightening, and straightening with automatic roll positioners. Automatic straightening is currently the subject of intensive research.
Each sector should have a matching straightener with specific features that can be adapted to the cross section to be straightened and to the properties of the process material.

Roller crosses/guides

Roller crosses/guides are used in the processing of endless material between the spool or coil, straightener, pull-off unit or processing machine. Their function is to guide and support the product to be processed.

The number and the arrangement of the roller crosses/guides in the material flow system are selected so that

  • sagging of the material is prevented,
  • sharp edges and deflections with small radii do not damage the surface of the material,
  • the endless material enters the next apparatus or machine in central position.

The diversity of roll guides results in a wide range of different applications. Which roll guide is selected will depend on the particular requirements. Roll guides are available as rigid and adjustable types. Adjustable roll guides are used when dimensions change and when exact positioning of the material is essential.

Centrally adjustable roll guides are suitable for a range of dimensions. The center of the material is retained even when dimensions change. The material itself does not have to be adjusted for it to enter the line centrally.

Some roll guides are designed to completely enclose the material while they guide it. Others are open on one side for better insertion of the material.

Roll diameter, roll material and clear widths depend on the dimensions and geometry of the material.
Burnished and hardened steel rolls are used e.g. for firm materials. Softer rolls made of PETP can be used for sensitive surfaces. The following basic types of roll are available:

  • with chromium-plating
  • hardened (up to 64 HRC)
  • with rubber coating
  • with ceramic coating
  • rolls made of PETP, PVC or polyamide

Rotary straightening

Unlike the roll straightening process, rotary straightening subjects the process material to alternating bends with a revolving bending axis.

The number of alternate bends depends on the speed of the product to be straightened and the number of rotations made by the spinner. Straightening blocks, straightening cheeks or straightening rolls are among the straightening tools used.

Rotary straightening is mainly performed in the production of rods or bars which permit a certain spring back of the material from the bending and torsion as the result of being cut to length.

It is sometimes wrongly assumed that two counter rotating straightening spinners neutralize the unwelcome stresses induced by torsion.

In view of the surface damage and sometimes severe impact on material parameters caused by the more aggressive forming of the product in the rotary straightening process, preference is being given more and more often to roll-type straighteners as the gentler alternative.

Semi-automatic straightening

Semi-automatic straightening is straightening with the use of offline and online data, basic automation equipment and at least one straightener. The offline and online data is relayed via the basic automation equipment to the straightener in order to achieve a defined and highly exact adjustment of the straightening rolls. A semi-automatic straightening system enables the reproducible adjustment of roller positions at any time.

The advantages of a semi-automatic straightener over a straightener with conventional roll adjustment are:

  • defined fine adjustment of the individual straightening rolls,
  • reproducibility of straightening roller positions within close tolerances,
  • application of high adjustment forces,
  • operation of the roll adjustment system from any location,
  • use of process data (data bases),
  • integration in a central control environment.

Simulation

Simulation is the representation of specific interesting properties of a system by the actions of a different system. By copying the behavior of a system in a simulation program it is possible to study behavioral characteristics or to examine variants. Simulation can be used at low cost and with little risk to identify behavioral patterns in time-consuming, costly, uncertain and hazardous processes.

With a simulation of the wire straightening process it is possible to pre-calculate the positions of the straightening rolls needed to prcduce a defined final curvature while taking due account of the parameters of the straightener (number of rolls, external roll diameter, roll pitch, groove width, groove angle) and of the wire (cross sectional geometry, elongation limit, modulus of elasticity, modulus of hardening, initial curvature, etc.). The simulation is based on a model of the elastic-plastic material characteristic under alternate bending and on the relationship between bending moment and curvature. Simulation of the wire straightening process also supplies data which can be used to determine the process forces.

Speed

In the forming processes employed in the wire producing and wire processing industry it is normal for the process material or workpiece to move relative to the tooling. Forming speed is one of the variables which characterize a forming process. It is derived from the degree of forming as a function of time.

Exemplary straightening tests conducted at different speeds of the process have proven that the final curvature and other parameters of the straightening process do not change significantly in the speed range up to approximately 10 m/s. At speeds above this limit, an identical adjustment of the straightening rolls results in a different deformation.