Knowledge Base

Straightening/definition

The term “straightening” covers the actions and measures needed to eliminate process-induced curvatures in the process material in order to produce a condition of straightness, levelness or defined curvature

Stretch-bend-straightening

The term “stretch-bend-straightening” is understood to be the bending of a material around rolls of small diameter with the simultaneous application of tensile stresses. Local plastic elongation occurs in those areas where bending tensile stresses are added to tensile stresses. Upsetting can occur, on the other hand, where the bending compressive stresses superimpose on the tensile stresses. However, the biggest part of the material's cross section is subjected to a tensile load. If such a process is performed by alternate bending, the product is stretched in steps, producing a final curvature in wire material and a flatness profile in strip material.

A stretch-bend-straightening system generally consists of an infeed unit for producing a reverse tension, a straightening unit for the bending or alternate bending, and an outfeed unit for applying a forward tension. For the purpose of straightening wire, the infeed unit can be e.g. a killing-straightener and the outfeed unit can be a drive unit. The straightening unit is either a conventional straightening system, a semi-automatic straightening system or a straightening system with an automatic roll positioner.

Stretch-straightening

In the stretch-straightening process the product to be straightened is subjected to a tensile force. This results in a tensile stress inside the workpiece, which superimposes on the existing internal stresses.

The tensile force is applied in sections and at a level of magnitude designed to produce plastic deformations in the material to be straightened.

Stretching limit

The stretching limit is a characteristic material parameter which can be determined in a tensile test. It is the stress defined as the internal force of resistance per unit of area perpendicular to the direction of load application with which a material reacts to an external tensile load of specific magnitude. At the stretching limit the deformation of the workpiece or the elongation of the tensile specimen due to the external tensile load continues to increase although the inner resistance remains constant or even decreases.

For process materials in the wire industry, where the materials used are preferable drawn wires, it is typical for the resistance to the load not to decrease at the stretching limit. Hence the stretching limit cannot be identified in the stress/strain diagram. DIN EN 10 002, the tensile test guideline for metallic materials, thus recommends determining an elongation limit at a non-proportional strain. Accordingly it is no longer the stretching limit, which is determined for drawn materials in the wire industry, but the elongation limit at a non-proportional strain of 0.2%. This is also referred to as the technical elongation limit.

The stretching limit or elongation limit at a non-proportional strain is a value used in the simulation of the WITELS-ALBERT wire straightening process for calculating the adjustments required to achieve a defined final curvature.

Swelling

The loading of a body by mechanical variables (forces, moments) produces stresses in the body, causing the body to deform in accordance with its material characteristics. The magnitude of the load decides whether this deformation takes place in the elastic or plastic zone.

Swelling is understood to be an elastic deformation which is reverted when the external load is removed. It consists of strains, compressions and bends. Every straightener and every straightening machine swells under the action of the straightening forces. It is a characteristic of straighteners, therefore, that the adjustment of their straightening rolls becomes smaller and the straightening gap larger, leading to changing results.

Each straightener has its own force/swelling characteristic, meaning its own specific deformation behavior. This characteristic has to be determined for the straightener in question if constant straightening results are to be achieved regardless of swelling.

Tensile strength

Tensile strength is a characteristic material parameter which can be derived form a tensile test. It is the stress defined as the internal force of resistance per unit of area perpendicular to the direction of load application with which a material reacts to an external tensile load of specific magnitude. At a material's tensile strength the deformation of the workpiece or the elongation of the tensile specimen due to the external tensile load continues to increase while only the inner resistance decreases in relation to the cross sectional area prior to the loading. The visual result of the tensile test is that the tensile specimen constricts locally at the material's tensile strength, whereas up to this point it stretched over its entire length. This constriction is the reason for the specimen's failure by breakage if subjected to further loading.

Tensile strength is derived from the quotient of the maximal load and the cross sectional area prior to loading. A material's tensile strength thus denotes its maximal endurable stress.