Knowledge Base

Deflecting

During the production and processing of wire the process material has to be deflected many times. To prevent disadvantageous changes to the initial curvature and material parameters, the material needs to be deflected elastically in the direction of its initial curvature. Elastic deflection depends on the diameter of the deflecting roll, which in turn depends on the process material's geometrical dimensions, modulus of elasticity, elongation limit and initial curvature. The permissible minimal value for the deflecting roll diameter is calculated with an equation.

The decoil-straightener from the WITELS-ALBERT range allows for elastic deflection in the direction of the initial curvature during the decoiling process. Decoil-straighteners for specific process materials can be built to order with adapted deflecting rolls. 
Minimal deflecting roll diameter:

D minimal deflecting roll diameter [mm]
d wide diameter or material thickness [mm]
E modulus of elasticity [N/mm2]
Rp0,2 stretching limit [N/mm2]
This equation applies only when the product is straight prior to deflection.

Deflection

The deflection h of a product to be straightened is the maximal distance between the chord a and the arc of the product. The deflection is expressed as mm/reference length.

The permissible deflection values for bars and wires are specified by DIN EN 10 21 8-2.

Drawing direction in the straightening process

Wire is formed on drawing machines to the required final diameter. The microstructure of the original wire is changed by the forming process. The image of the ensuing microstructure is also known as the "drawing texture". The draw ratio is derived from the quotient of the cross sectional reduction and the initial cross section. The higher the draw ratio, the greater the stretching of grain in the direction of the wire axis. Plastically formable components of the microstructure (e.g. tough ferrite crystals in iron and steel wires) follow the forces in forming direction. Brittle components (e.g. pearlite crystals) are crushed under the action of the forming force and then aligned in drawing direction.

Straightening tests have shown that final curvatures differ when the material is drawn through the straightener in different pull-through directions. With wires that are difficult to straighten, it is an advantage to perform the straightening in drawing direction.

Drive unit

Endless material must not only be straightened, it must also be transported, pulled or pushed.
Generally this is the job of the actual processing machine. Where a process is divided into various steps, drive units may be integrated upstream and downstream from the process. Dividing the process into several steps also helps to reduce process stress.

Drive units are feeding devices which clamp the material to be pulled or pushed between two or more pairs of rolls or caterpillars, using motor power to apply a tensile force. Any type of controlled or uncontrolled motor may be used according to the application. The contact force of the drive rolls or caterpillars is applied pneumatically, hydraulically, by electric motor, or manually. The level of contact force depends on the tensile force needed to move the material by frictional locking. On the one hand it must be selected high enough to move the material without slippage. On the other hand it must not be too high in order to prevent plastic deformations and surface damage.

Drive rolls are generally made of hardened steel, although other materials such as plastic, Vulkollan(r) or the like are possible. Roll profiling depends on the geometrical shapes of the materials to be transported.

Users are also free to specify any V-belt coating from the range on offer.

Different drive units have been developed for various areas of application: 

  • one driven pair of rolls with unilateral bearing  NA
  • one driven pair of rolls with bilateral bearing NAB
  • two driven pairs of rolls with unilateral bearing NAD,NADV
  • two driven pairs of rolls with bilateral bearing  NADB
  • two drive belts with unilateral bearing NAK

Drive units are easily combined with other components, e.g. straighteners, roll-type guides, hydraulic units and pneumatic units. The resulting machine modules support existing production lines.  

Final curvature

The result of a straightening process is expressed e.g. by the final curvature of the product to be straightened. Basically there can be two objectives: to create a straight product, i.e. a final curvature of zero within the set tolerances, or to produce a defined final curvature other than zero. Which of these two objectives applies will largely depend on the process which follows the straightening.

To guarantee final products of constant positive quality it is important to produce a final curvature that is as constant as possible. A changing final curvature goes hand in hand with varying process transitions and ultimately leads to final products of fluctuating quality. 

Friction

External friction is the inhibition of relative movement between touching bodies. In the case of solid bodies, friction is mainly based on microscopic unevenness. The frictional values of different materials relative to each requires special attention in this connection. Internal friction is the friction between parts of the same body. In liquids this friction is called viscosity.

During the straightening process, friction occurs mainly in the straightening rolls. It consists of the following components, which together add up to the total running resistance: rolling and sliding friction of the rolling elements and cages relative to each other, lubricant friction and seal friction. The aim must be to keep the friction as low as possible by ensuring an acceptable bearing load and optimal lubrication.

Friction leads to “losses”, i.e. kinetic energy is converted into frictional energy. This energy fraction is therefore no longer available for use in the production process.