Knowledge Base

Straightening plane

The commonly held idea that the position of a straightener's body corresponds to the straightening plane is wrong.

Basically, the straightening plane is defined by the axial position of the straightening rolls. If this is horizontal, then the straightening plane is horizontal. The same applies to the curvature plane in which the product to be straightened is fed in or bent.

With a vertical axis we speak of a vertical straightening and curvature plane.

The most frequently used arrangement is the double straightener, which eliminates the initial curvatures in two planes (horizontal/vertical).

You may well ask what happens with the other curvature planes lying outside the two straightening planes? Their processing is possible at best on a random and sporadic basis or not at all.

Hence it is important when producing wire to maintain a constant curvature course and not to leave the curvature plane.

A constant straightening plane can only produce constant final curvatures from constant curvatures in the same plane.

Where this is impossible for whatever reason, the use of killing-straightener, and helix straighteners in straightening systems can prove very useful.

Straightening process set-up

A correct straightening process set-up depends on an analysis of the product to be straightened, an analysis of the straightened material production process, and an analysis of the final product. A specific procedure has to be followed in order to choose the correct straightening system, the correct number of straightening rolls, and the correct location of the one or more straighteners.

The purpose in setting up a straightening process is to determine the status quo from the essential analyses and to define the production steps and corresponding equipment needed to obtain the final product. Using our knowledge of the process we can create constant process transitions, i.e. output and input parameters, in order to produce constant final results.

Constant and reproducible straightening roll settings based on the constant input parameters known to us at the beginning of the straightening process result in a constant final curvature.

If all these aspects are duly considered, the straightener will provide optimal processing conditions for obtaining a final product of the required quality.

Straightening roll

A straightening roll is the last link in a straightener's modular design chain and the component exposed to the greatest wear. Its design, production and use thus deserves special attention.

The following criteria are particularly important:

A) Materials
The raceway of a straightening roll is subjected during roll-over to local loads which find
expression in high Hertzian surface pressures. The raceway material should be selected so that
ideally through-hardening but at least the necessary depth of hardness and a surface hardness
of 670-840 HV is achieved. The material normally used is through-hardening steel according to
DIN 17230, e.g. 100 Cr 6.

B) Bearing arrangement design
The bearing arrangement for a straightening roll is that of a locating bearing. The shaft or pin end provides radial support as well as axial guidance. Radial bearings able to absorb combined loads, e.g. radial ball bearings, angular contact ball bearings or track rollers, are suitable for use as straightening rolls. To enable the bearing's load capacity to be used to the full, the cylindrical contact faces need to be firmly and uniformly supported over their entire circumference and across the full width of the raceway. Perfect radial mounting is also vital.

C) Dynamic/static load rating
A straightening roll's dynamic load capacity depends on the fatigue behavior of its material. Fatigue time is an expression of useful life and depends on the straightening roll's loading and speed as well as on the statistical probability and random timing of the first incident of damage. Static load capacity, on the other hand, is limited by the plastic deformations produced in the raceways and rolling elements by a high resting load.

D) Bearing capacity and life-time
The size of bearing required for a specific straightening process depends firstly on the straightening range of the straightening roll. A further factor, however, is the magnitude of loading. This is expressed by the dynamic load rating C and the static load rating Co. A straightening roll's useful life is defined as the number of rotations made by its bearing before the first signs of material fatigue are noted on a raceway or rolling element.

E) Friction, speeds, and temperature
A straightening roll's frictional moment depends on many factors such as load, speed, condition of lubrication and seal friction. The maximum possible speed of a straightening roll is mainly defined by the permissible operating temperature of the rolling bearing. In other words, speed depends on the type of load, the conditions of lubrication and the conditions of cooling. A straightening roll temperature of 70°C is considered normal.

F) Dimensional, geometrical and bearing tolerances
A straightening roll's dimensional, geometrical and bearing tolerances comply with tolerance class PN conforming to DIN 620.

G) Installation and dismantling
The smooth and troublefree operation of Witels straightening rolls largely depends on the care with which they are installed and replaced. Inner rings have to be mounted on the shaft or pin so that the mounting force is evenly distributed over the front face of the inner ring. The mounting force must not be transferred to the rolling elements.

H) Lubrication, maintenance and corrosion protection
For straightening rolls to perform reliably they require sufficient lubrication to prevent direct metallic contact between the rolling elements, raceways and cage while at the same time reducing wear and protecting surfaces from corrosion. All straightening rolls are supplied with grease lubrication as standard.

J) Storage of straightening rolls
Although Witels straightening rolls are always delivered with life-time lubrication, they cannot be stored indefinitely. Under certain circumstances a straightening roll kept in storage for a long period may initially display higher frictional moments than one fresh from the factory. Nor is it possible to rule out deterioration or even gumming of the grease charge in the course of prolonged storage. Attention is drawn in this connection to the WlCAS cassette system, which finds use mainly in problematic applications for straightening rolls.

Straightening roll groove

The profile cut into the outer ring of a straightening roll is called the straightening roll groove. Its purpose is to accommodate and guide the product to be straightened.

Angular grooves of 90°, 100° or 110° are normal for round, solid material. They are particularly advantageous for straightening ranges, i.e. wire of different diameters.

Profiled, soft or tubular material, on the other hand, is straightened in grooves which are adapted to the material to be straightened to produce a non-slip fit. Smooth, unprofiled rolls are used to flatten strip material.

Straightening roll life-time

The dynamic load capacity of a straightening roll depends on its material fatigue characteristics and wear. Useful life depends on the straightening roll's loading, speed, conditions of lubrication, soiling, installation and temperature, the statistical probability of the first incidence of damage, and diverse other factors. All too often the impact of dirt is underestimated.

The load capacity and useful life of straightening rolls from Witels are determined by the methods customary in rolling bearing practice. At the same time allowance is made for the fact that the outer ring undergoes elastic deformation through contact with the product to be straightened. Compared to a rolling bearing supported in a housing bore, there is a different distribution of load in the bearing and bending stress in the outer ring. We differentiate between internal and external factors with an influence on wear.

Contact between the product to be straightened and the outer ring results in the following external factors:

  • material of the outer ring
  • material and surface consistency of the product to be straightened
  • speed
  • slip
  • soiling and lubrication

Internal factors with an influence on straightening roll wear are:

  • lubrication of the bearing
  • type of bearing
  • dynamic and static bearing load
  • speed
  • seal arrangement
  • elastic deformation

Straightening system

A straightening system is understood to be a combination of straighteners which, duly adapted to the product to be straightened, transform difficult and sometimes alternating initial material parameters into constant values.

The constant process transition thus obtained is essential for designing controlled follow-up processes.

The simplest straightening system generally consists of two individual straighteners arranged in different planes and mounted using a connecting bracket. Acceptable, constant results are achieved in many applications using a simple straightening system of this type.

If the initial parameters of the product to be straightened change during the process and if, for example, curvature fluctuations or helicities arise, then it will be necessary to use problem-related tools and jigs such as helix straighteners, killing-straighteners, etc.

A straightening system set-up consists accordingly of a clearly structured straightening process sequence. Fluctuating initial parameters require greater structuring of the straightening process to achieve a defined and constant final curvature. Simply increasing the number of straightening rolls would have little effect in this case.

The first priority is to transform changing curvatures in different planes into a constant curvature in a single plane. This is the essence of a successful straightening process with constant final curvatures.